February 4, 2020 Home Cleaning

How to Remove Glue from an Installed Wooden Floor

Installing a hardwood floor can be an arduous process, and it may leave a mess behind. Besides dust and wood shavings, you might come across some blobs of glue glue which was vital to the installation. Think of this as a temporary issue and attack it first with ice to literally freeze the glue. Failing that, ramp up your efforts with some other household goods. In no time, you will agree the fuss and bother of installing the hardwood flooring was well worthwhile.

Poke in the glue with a cotton swab to determine its resiliency factor. If some or all of the glue lifts, then you are able to safely clean out the place on the floor. If the glue will not budge, prepare to provide the ice plenty of time to work.

Cover the glue place with a paper towel to supply some protection into the wooden floor as the ice melts.

Place several ice cubes in a plastic sandwich bag. Ensure there are sufficient ice cubes in the bag to fully cover the glue spot on the floor.

Set the sandwich bag full of ice above the paper towel along with the glue place. Weigh down the bag with a heavy object to speed the procedure, if at all possible. A brick is excellent for this particular job; a hefty novel is a worthy substitute.

Check the glue place every 30 minutes. Pry in the place with a cotton swab to assess its consistency. If it becomes hard and brittle, push the glue place to break it away from the floor, with the cotton swab.

Ramp your attempts using spray lubricant into the dried glue. Allow it to sit for 20 minutes. Pry the glue away with a cotton swab. Wipe the area with a moist cloth.

Open your refrigerator and your kitchen pantry and choose products that contain natural oils or acidity to break down the glue residue. One at time, rub mayonnaise, lemon juice, peanut and white vinegar on the blob of glue. Allow each to sit a minimum of 20 minutes to break down the glue. Wipe away the glue, using a moist cloth.

Clean out the place on the floor after the glue is removed, using a hardwood floor cleaner or a damp sponge and a little gentle soap.

See related

February 1, 2020 Wine Cellars

Five Different Varieties of Dwarf Apple Trees

Dwarf apple trees have many advantages over standard apple trees. You can develop them in tiny spaces and easily prune, spray and harvest them. Later planting, dwarf apple trees produce fruit much sooner, usually after three decades, than standard apple trees, which may take up to 10 years to make. Dwarf apple trees are created by grafting a apple variety to a dwarf rootstock. The complete size of a dwarf apple tree also depends partially on cultural states and pruning methods. To fruit nicely, apple trees need a frightening period, a period with temperatures of 45 degrees F or less. Many dwarf apple tree varieties possess a very low chill requirement, thriving and producing apples in warmer climates.

Arkansas Black Dwarf Variety

The Arkansas Black apple tree (Malus domestica Arkansas Black) is available as a dwarf or semi-dwarf tree. The dwarf tree will grow 6 to 9 feet tall and the semi-dwarf tree will reach 8 to 10 feet in maturity. Ten years after planting , these apple trees are regarded as mature. The Arkansas Black apple is flavorful and great for eating fresh, cooking or making juice. Trees have great disease resistance, especially against cedar apple rust disease. Arkansas Black dwarf varieties grow well in U.S. Department of Agriculture plant hardiness zones 5 through 9. These trees cannot self-fertilize and have to be pollinated by the other neighboring apple tree variety.

Goldrush Dwarf Variety

The Goldrush apple tree (Malus domestica GoldRush) functions as a dwarf (6 to 9 ft) or semi-dwarf ( 9 to 12 ft) tree. Goldrush is easy to grow and produces a large apple harvest. The yellow-orangey apples are flavorful and sweet, especially after they are stored for a while. They are great eaten fresh or used in cooking. The Goldrush apple tree is disease-resistant, especially to scab and mildew. Goldrush is self-sterile, so it needs to be pollinated by another apple tree variety neighboring. All these trees grow well in USDA zones 5 through 9.

Gala Dwarf Variety

The Gala apple tree (Malus domestica Gala) grows 8 to 12 feet tall at maturity. The Gala apple is a frequent apple in supermarkets, but it’s a whole lot sweeter when newly selected. The orangey-red Gala apple is very good for eating fresh or making juice. The tree grows well in USDA zones 5 through 9. However, the tree needs to be sprayed, because it’s inferior pest and disease resistance, especially against scab. The Gala apple tree is partially self-fertile, meaning it can take fruit without pollination by another apple tree. However, pollination from another apple tree variety will likely enhance fruit-bearing.

Fuji Dwarf Variety

The Fuji apple tree (Malus domestica Fuji) can be implanted as a dwarf or semi-dwarf tree. The Fuji apple is an attractive yellow apple with a reddish-pink overlay. The apple has a mild, sweet flavor and is great when eaten fresh. The tree enjoys warm spaces and a very long season. It favors USDA zones 6 through 9, though under the right conditions, it may also be successful in zone 5. The tree contains average pest and disease resistance. It is self-sterile and needs to be pollinated by another apple tree variety.

Granny Smith Dwarf Variety

The Granny Smith apple tree (Malus domestica Granny Smith) attains a height of 8 to 12 feet at maturity. It grows well in USDA zones 6 through 9 and occasionally even in zone 5, though apple ripening may not occur. The Granny Smith apple tree originated in Australia, but now is a popular variety in the USA. The green apple is tart, great for eating fresh or in cooking, especially for baking apple pies. The tree contains average pest and disease resistance and is self-fertile. It does not have to be pollinated by the other tree variety, although fruiting may be raised by a harmonious nearby apple tree variety.

See related

January 30, 2020 Home Painting

The way to Incorporate a Wood Chair to Appear Like Wrought Iron

Wrought iron is a timeless design component in Tuscan and Mexican furniture, but it might be pricy. In addition, it can be exceptionally heavy, which makes moving it tough, particularly if you have young kids joining you at the table. New paint technologies which incorporate iron particles at a paint base allow it to be not only possible, but nearly effortless, to get that wrought iron look on lightweight timber.

Cover your work surface with a drop cloth. Lift the seat on a table or workbench to make it a little easier to achieve, if you have one available.

Remove the seat if it’s upholstered and can be unscrewed from the seat frame. If the upholstered seat doesn’t come off, then cover the fabric with plastic garbage bags held in place by painter’s tape.

Sand the seat with 220-grit sandpaper to remove the surface shine and assist the tip stick to your seat more effectively.

Wipe the seat down with tack fabrics to pick up all the sanding dust.

Put on your eye protection and painter’s mask. Apply a thin coat of spray-on wood tip to help the paint stick to your seat. Keep the spray may moving in constant back and forth movements to avoid letting the primer puddle up in any one spot. Let the primer dry according to the period mentioned on the tag.

Mix together the paint and particles if you’re using two-part iron powder paint, or shake the can well if you’re using a spray. Use the paint in a thin, even layer, stopping frequently to shake or stir your paint so that the iron particles don’t settle on the bottom.

Let the iron powder paint dry according to the time on tag, adding 30 to 60 minutes for rainy days or a generally damp climate, prior to deciding if you need another coat.

See related

January 25, 2020 Wine Cellars

The Best Plants for Aeroponics Systems

An aeroponic garden provides you with an innovative way to grow flowers and vegetables by employing an air mist environment without dirt. Aeroponic research led by NASA took off from the 1980s and has since demonstrated that aeroponic procedures work well with a huge array of plants. Lettuce and herbs are among the plants best suited to a house aeroponics system, which makes it feasible to grow plants inside year-round.

The Basics

In an aeroponics system, plant cuttings or seeds are suspended mid-air in a growing chamber, as a mist of nutrient-laden water is continuously sprayed on the roots of plants. Aeroponics systems are often used in a protected environment such as a greenhouse, in which environmental conditions like temperature and humidity can be controlled. Sunlight is the primary light source, with some supplemental lighting.

Benefits

An aeroponics system minimizes water usage by 98 percent, fertilizer by 60 percent and pesticides by 100 percent, according to NASA. The deficiency of dirt provides maximum root aeration and maintains roots dry, reducing the risk for diseases. Seedlings may be healthier because they don’t stretch or wilt while roots are forming. Harvesting can also be easier, particularly for root crops, and because plants grow faster, crops can be planted and harvested from the system throughout the entire year.

Vine Plants

Rumors normally must be commenced in pots and then descend to the ground after four weeks. With an aeroponics system, tomato crops can be started from the growing chamber and transplanted just 10 days later. Instead of a couple of tomato harvest cycles each year grown the traditional manner, aeroponic growing may yield up to six tomato crops annually. Based on “The Telegraph,” at the Greenwich Village restaurant Bell Book & Candle in New York City, chef John Mooney successfully grows tomatoes, tomatillos, eggplant, strawberries and watermelons in a rooftop aeroponics system. He adds that the only plants that he can not develop aeroponically are fruit trees and vegetables that grow underground, like potatoes, beets and carrots.

Leafy Greens

Research at the Cornell University Cooperative Extension has found that aeroponics is the most efficient way of growing leafy greens. Greens may get contaminated with dirt pathogens and bacteria such as e.coli, but aeroponics greatly reduces these risks. Chef John Mooney has had success with several varieties of lettuce with his rooftop aeroponics system and adds that while it requires a gallon of water to grow a head of lettuce over four weeks, a tower aeroponics garden uses 1/10 of the water since the excess is continually cycling back into the system to be reused.

Herbs

Aeroponics has been tested to develop cleaner, more constant herbs such as burdock at the University of Arizona’s College of Agricultural and Life Sciences. Growing such herbs aeroponically is much less labor intensive than conventional procedures, and leads to a greater density per square foot of greenhouse space than traditional greenhouse growing. Mints, skullcap, stinging nettles, ginger and yerba mansa have also already been successfully tested in aeroponics systems, resulting in earlier increase, higher yields and multiple harvests.

See related

January 21, 2020 Tropical Style

Honeysuckle Butterfly Bush

With its delicate yellow blossoms and compact development, the “Butterfly” bush honeysuckle (Diervilla sessifolia “Butterfly”) is an appealing choice if you want to put in a new tree into your own garden. This plant shouldn’t be confused with the invasive butterfly bush (Buddleja davidii) which is banned for sale in several nations. Although low-maintenance, you must know about this bush’s growing demands before you make your purchase.

Size and Appearance

A mature “Butterfly” bush honeysuckle grows to about 5 feet tall and wide. The coppery new growth provides a colorful display in spring. The leaves turn dark green as they mature. From spring through the summer, the bush produces clusters of trumpet-shaped, pale yellow flowers which attract butterflies and hummingbirds. Although deciduous, the red stems of this “Butterfly” bush honeysuckle add a little color to the garden in winter.

Where to Grow

The “Butterfly” bush honeysuckle grows best in U.S. Department of Agriculture plant hardiness zones 4 through 9. The tree should be planted in either full sunlight or partial shade. If grown in full shade, the plant will get leggy and, if it blooms whatsoever, the flowering will be minimum.

Soil Needs

The “Butterfly” bush honeysuckle is going to do well in most soils but grows best in well-drained, loamy soil. Soil pH is not a issue with this plant, but drainage is. The tree will not thrive in areas of standing water or if it is planted in heavy clay soil because the poor drainage can lead to root rot.

Care and Maintenance

Once established, the “Butterfly” bush honeysuckle is a low-maintenance plant. It can also tolerate short periods with dry dirt. During dry spells, water the tree intensely when you first notice the leaves wilting. The plant does not need regular feeding, but can be mulched with compost to provide nutrients. In late February or early March, prune your “Butterfly” bush honeysuckle to remove any dead branches and to thin out and shape the tree. The plant can send out suckers and these should be cut to the ground when they look.

See related

January 18, 2020 Home Painting

The best way to Polish Stained Concrete

A concrete floor can be stained to a number of shades and colours, and when that floor is correctly polished, the floor will be durable and almost maintenance-free. A special concrete polishing machine is required for the job, along with sanding discs varying from coarse to very fine. In many cases, it is possible to find a concrete polisher for lease at a local tool rental store, though you will probably have to get the polishing discs to match onto the polisher.

Sweep the floor thoroughly with a stiff-bristled push. If the ground has been exposed to water at all, permit the ground to dry for a few days before starting the polishing.

Attach a tough polishing disk (30- to 40-grit metal-bonded diamond) into the mat on the bottom of the polisher. Put on a dust mask and a pair of safety glasses, turn on the polisher and perform the dry polishing pad above the ground. Move the polisher in small circles along a linear path from one side of the room into another, then transfer past a row and work your way back, taking care to create a pass over the entire ground without working over any places over once to maintain the ground even.

Sweep the ground thoroughly, then switch into a medium-coarse (80-grit metal-bonded diamond) polishing pad and repeat. Follow up with a dry sanding with a medium pad (150-grit metal-bonded diamond).

Apply an even coat of penetrating concrete sealer to the full ground and allow the sealer to soak in the coarsely ground concrete floor for the amount of time recommended by the manufacturer.

Mop the floor with clean water to remove any deposits created by the polishing. Then, switch to a medium resin-bond diamond polishing disk (100-200 grit) and run evenly the polisher above the wet ground. Change to a nice resin-bond diamond polishing disk (400 grit), tighten the water from the mop bucket, clean the floor thoroughly with the mop, leaving ample clean water onto the ground, then make another pass with the polisher.

Keep on polishing and cleaning using progressively finer resin-bond diamond polishing pads above the wet ground till you finish with the finest pad you’ve got available (1,500-grit metal-bonded diamond or greater).

Give the ground a final mopping and touch up any areas that need extra buffing with the fine-grit pad.

See related

January 14, 2020 Tropical Style

When Do Willows Bloom?

Willow trees’ booming stage begins in February in warm areas, and it continues until June in colder climates. The trees’ long, tube-shaped blossom clusters called catkins produce their appearance just before leaves reappear on the branches. The flower clusters are full of nectar, which insects continue for pollination. Within 45 to 60 days after pollination, willow seeds are ripe and ready to begin another reproduction cycle.

Description

Willow trees are characterized by long, narrow, pointed, slightly serrated leaves that are yellow green on the top and also have a white or light-green underside. Leaf color changes within the yellow-green range according to species. Most varieties are deciduous. All willows are dioecious, producing female or male catkins on separate trees. Willow seeds are from fruits located just on the female trees. The trees begin to reproduce by airborne seeds after 10 years. They grow quickly and live 55 to 70 years.

Blooms

Willow trees with springtime bloom patterns include pussy willow, weeping willow and black willow. Salix caprea, also known as pussy willow, great sallow and goat willow, produces bright-white, slightly fuzzy blossoms on the male trees. The catkin flowers are 1 to 2 inches long, and each blossom is composed of numerous hairlike protrusions. The blossoms mature to yellow until they are disbursed by rain or wind. Both weeping willows and black willows have yellow, tubular-shaped blossoms. Black willow flowers open and float away, looking like white mist, even when they are pollinated.

Reproduction

The optimum age for a willow tree to reproduce is 25 to 75 years old. Willows produce large volumes of seeds each spring after the blooming phase. Seed capsules are light brown. At maturity, the capsules split open and release tiny, green seeds. Each fertilized seed has long, silky hairs that act as wings, allowing the seed to travel a long distance before falling to the ground. Willow seeds are distributed widely by water and wind. Each seed has a 12- to 24-hour time period in which to land and germinate. The seeds germinate best in quite moist soil conditions. Willow tree roots are propagated easily through cuttings. Roots form shallow networks near the ground.

Supply

The genus Willow (Silax) contains 90 varieties widely distributed across the eastern portion of america. Black willows, Scouler or mountain willows and Hooker willows are varieties often found in american U.S. zones. Willow trees adapt to many soil conditions but prefer a moist environment. They’re cultivated for erosion control since their extensive interlocking root systems form a barrier against water. Some non-native willow species are identified from the U.S. Department of Agriculture Forest Service as invasive plants due to their vigorously spreading root systems that overwhelm native vegetation. In traditional cultures, willow trees are valued as an early source of pollen for bees, as an excellent weaving material and for use in seasonal ceremonial practices.

See related

January 11, 2020 Home Cleaning

How to Clean a Shower Curtain Using a High-Efficiency Machine

Whether you’ve got a cloth shower curtain with a plastic lining or just one faux curtain, most shower curtains are washable, including in high-efficiency machines. The procedure removes dirt and soap scum accumulation. For synthetic drapes, handy, premeasured detergent and bleach cups create cleaning in front-loading, high-efficiency washers easy. If you’ve got a fabric curtain, read the manufacturer’s washing instructions, so you choose the right detergent and temperature options.

Synthetic and Vinyl Shower Curtains

Synthetic shower curtains have a fresh, crisp look in a toilet, and cleaning is straightforward. After detaching the curtain in the pole, put it in the drier, untwisting it to make certain that water reaches into the crevices. Place the detergent and bleach or premade cup to the high-efficiency drier, picking out the white or hot cycle to make sure that dirt particles and mildew are fully dislodged in the curtain.

Fabric Shower Curtains

Fabric shower curtains require more consideration; read the product care tag in detail. Harsh cleansers, such as chlorine bleach, cause color fading, and bleach erodes water-resistant substances on some drapes. Soap-scum buildup is often the offender. Overuse of high-efficiency detergent ends in detergent deposits, particularly with one-item washes, however substandard detergent does not eliminate mildew. Fabric drapes shrink when drier settings are too hot. If the care directions forbid bleach, then add vinegar as opposed to combat the mildew and other dirt.

See related

January 7, 2020 Home Cleaning

Best Ways to Clean Vinyl Seats

Whether you’ve got outdoor seats made from rigid vinyl or indoor ones covered using flexible, leather-like vinyl, the procedure for cleaning them is similar. Vinyl — more correctly called polyvinyl chloride, or PVC — is nonporous and vulnerable to powerful solvents, so only gentle cleaning supplies and methods are advisable.

Cleaning Soft Vinyl

You can frequently clean soft vinyl couches, chairs as well as automobile or boat chairs with nothing more than a damp rag. Should you want more cleaning power, you shouldn’t use anything stronger than dish soap or even all-purpose cleaner. Mix a ounce or so per gallon of warm water, and rinse with a rag or sponge. If you need to remove mildew, do it using a 4-to-1 combination of water and chlorine, but test this in an inconspicuous spot first to make certain it doesn’t cause any discoloration. Never use abrasives, powerful bleach or wax.

Cleaning Hard Vinyl

The process for cleaning hard vinyl is similar to that for cleaning delicate vinyl — with the exception that you can safely use baking soda as an abrasive to remove scuff marks. Wet the vinyl; sprinkle on some baking soda and rub it with a cloth, and rinse with clear water. You can also remove scuff marks, as well as dye stains, by massaging with denatured alcohol. After washing your hard vinyl chairs, protect them and maintain them shiny by coating them with car glue.

See related

January 4, 2020 Home Cleaning

How to Clean Tough Water Stained and Soap Scummy Shower Doors

Those filmy shower doors are not doing anything to the bathroom decor, and you may have noticed that a once-over with soap and water does not get rid of the soapy film or hard water stains. It is possible to prevent the soap scum by showering with liquid soap rather than bar soap, and if you squeegee the glass, then you are never going to have hard water deposits. Those are good strategies for the future, but now that the damage is finished, you may need to try some cleaning hints.

Start With the Soap Scum

You might already have some bathtub gloves, but should youn’t, you can buy a set for a few dollars. They’re made of nylon or fiber mesh and made to be somewhat abrasive, which is a handy feature for cleaning glass and metal — just jump in the shower, lather up the gloves with liquid soap and wash off. The gloves get into tight corners, but you may need the support of a toothbrush. When you turn on the shower and rinse the glass, then the soap scum ought to be gone, but the task isn’t finished.

Acid to the Rescue

The glass may appear crystal clear after rinsing and washing it, however, hard water marks often reassert themselves when the water disappears and the glass dries. The marks are brought on by the vitamins that make the water “hard .” Soap will not emulsify these deposits and loosen their bond, so it is useless to attempt to scrub them. Instead, you need to dissolve them with an acid. That may sound extreme, but you also need only a mild one, and you also have two good candidates in the kitchen — lemon juice and vinegar. In a pinch, you may even utilize a delicious soft drink — the tanginess means the soft drink includes an acid — typically phosphoric or citric acid.

Misting to Remove Minerals

Whether you choose vinegar or lemon juice, it is best to use it full strength: simply pour it straight from the bottle to a spray bottle. If you’ve just rinsed the glass, then wait for it to dry; then generously mist it with the sprayer. The acetic acid in vinegar or citric acid in lemon juice both need time to get the job done. Ideally the glass ought to stay wet for 10 to 30 minutes; you may need to mist one or two additional times to avoid the glass from drying out. After scrubbing with the rubbed and rubbed with the shower head, the hard water deposits should be gone.

A Glue for Stubborn Stains

The most troublesome parts of a shower door to wash are the metallic frame, the hinges as well as the handle, and misting may not get the work done unless you repeat it many times. There is a better means to do it: Make a paste using borax or salt and distribute it on the stain with a toothbrush. It may take one hour or more for the paste to work, but when you return and scrub the stain with the toothbrush, then it should come right off. If not, just repeat the therapy until it does.

See related